What did you do to your Ranger Raptor Today?

[josefmd]

Yesterday, but did first oil change @1500 miles, and checked rear diff fluid level.

Sponsored

 

[Peter949]

Oops

good thing i'll be replacing stock rails/steps with rocky roads in a few weeks.

Full send or crawling?

 

[Mystic]

Full send or crawling?

This particular instance was crawling (OK / Brooklyn Mine trails out in JT).

That being said...I've jumped and sent this thing hard in Ocotillo and no issues, performs like a champ.

Factory sliders gotta go for any serious crawling.

 

[LordRaptor]

I finally got my new wheels!

Black Rhino Etosha wheel w/+20mm offset. The wheel fits perfectly, and as you can see from the picture with the level, the tread pattern sits almost flush with the top of the wheel arch. I also used the stock KO3 tires.

I'm so happy with it, and the bronze wheel on Cactus Gray looks sooo good!

Nice! Do you think a leveling kit is required for that +20mm offset?

 

[rwolfcastle]

Nice! Do you think a leveling kit is required for that +20mm offset?

No leveling kit required. I've had zero issues with it.

 

[J.Dub]

Oops

good thing i'll be replacing stock rails/steps with rocky roads in a few weeks.

Looks like you had a fun time!

 

[Bt_okst]

Hated fit and look of factory seat covers, so replaced with katzkin.

 

[Dutch]

Added XL mudflaps - removed floorboards.
Win/win/win -----

 

[Truckin]

Hated fit and look of factory seat covers, so replaced with katzkin

Looks good. What
Do those run $$ and do they make them for a lariat?

 

[Bt_okst]

Looks good. What
Do those run $$ and do they make them for a lariat?

Should be go able to build on katzkin site for any ranger. I pd 1300, but I've seen people pay almost 2000 for same thing. Depends on the installer and your relationship with them

 

[chasvs]

Installed the Bronco under seat vent extenders in my RR. Fit fine and gives a little more reach under the seat and tilted end with a nice grille. Better than what was there before.

 

[rocsteady]

I had the undercarriage protected with fluid film. I felt great about it until I looked under and saw my beautiful orange shocks coated in the fluid film and the road dust and dirt that sticks to that stuff. I couldn't bring myself to take a picture; I just laid on the ground and sobbed quietly to myself.
I may not be able to stand that. I love the look of those beauties from FOX and I always crawl under to wipe them down when I wash the car so I might just continue doing that. Time will tell.


Today I added one of the Ford swing out boxes, 38000 Ford reward points that I got for buying the Raptor, knocked, wait for it, $190 off the price. So for $52, I went for it. Fit all my ratchet straps, bungees, reflective vest, and portable air compressor.
(pro tip: scrape the line-x/spray-in bedliner completely out of the torx head of the bolt that holds the tie downs in BEFORE you try to take them out. Had to use some obscenities early this week as I struggled to get the bit to fit properly into the first bolt I attempted to remove. They do then reinstall over the box mount).

 

[dmac72]

Got the ProCal4 tune installed today! I don’t know if it added as much horsepower as my stubby antenna, but the truck is noticeably zoomier!

 

[rwolfcastle]

I had the undercarriage protected with fluid film. I felt great about it until I looked under and saw my beautiful orange shocks coated in the fluid film and the road dust and dirt that sticks to that stuff. I couldn't bring myself to take a picture; I just laid on the ground and sobbed quietly to myself.
I may not be able to stand that. I love the look of those beauties from FOX and I always crawl under to wipe them down when I wash the car so I might just continue doing that. Time will tell.


Today I added one of the Ford swing out boxes, 38000 Ford reward points that I got for buying the Raptor, knocked, wait for it, $190 off the price. So for $52, I went for it. Fit all my ratchet straps, bungees, reflective vest, and portable air compressor.
(pro tip: scrape the line-x/spray-in bedliner completely out of the torx head of the bolt that holds the tie downs in BEFORE you try to take them out. Had to use some obscenities early this week as I struggled to get the bit to fit properly into the first bolt I attempted to remove. They do then reinstall over the box mount).

I'm looking at getting the toolbox. Do you think the bracket will fit over the Ausmotion air compressor mount?

 

[quickstang1]

Hated fit and look of factory seat covers, so replaced with katzkin.

Those look great!!

Sponsored